logo

• Pumps, Boosters, Fire-fighting systems
• Agents, Importers, Manufacturers
iso

  

  flag-en

banner

 Products > Surface centrifugal pumps >TELLARINI pumps

 

 Bronze pumps   Manual
     

EEM20
EEM 20
EEM 25-40
EEM 25-40

Specifications

 

EEM series (normal)
The best solution for transfers of liquids because of the high self-priming capability, the possibility to operate with discontinuous presence of the liquid at the suction and the reversibility of the flow. The particular tight structure of the pump body avoids the contact between the liquid and the motor and prevents losses. They are used for home uses, gardening, agriculture, (oils, wine, must, sea water, diesel) etc.

SPECIFICATIONS
- Max flow 9 m3/h ,max head 26m
Height of priming 6 meters 
-Possibility to reverse the flow
-Asyncronous single-phase motor, protection IP 44, with switchreverser
-Continuous Duty
-Pumps are supplied with one straight fitting and one curved fitting.
LIQUID 
-Max temperature 90° C 
-Max density 1.1 g/cm3 
-Without hard particles (e. g. sand) 
-Not too viscous 
-Examples: water, sea water, gasoil, oil, anticryptogamics, etc. 
-Do not use with petrol, solvents and, in general, in places presenting the risk of explosion and fire
MATERIALS
-Pump body: bronze
-Impeller: bronze
-Shaft: stainless steel AISI 316
-Counterflange (EEM 20): stainless steel AISI 304

GASKETS / SEALS
- Lip seal in NBR with stainless steel spring 
- O-ring between body and cover in NBR 
- (only EEM 20) Counterflange gasket in Guarnital
POWER SUPPLY 1~
- Standard: 230 Volt / 50 Hz
- On request:
- 110 Volt / 50 Hz, 110 Volt / 60 Hz, 220 Volt / 60 Hz

     
ENM 20
EN 20
ENM 25-50
EN 25 έως 50

Specifications
 

EN series (professional)
The best solution for transfers of liquids because of the high self-priming capability, the possibility to operate with discontinuous presence of the liquid at the suction and the reversibility of the flow. The particular tight structure of the pump body avoids the contact between the liquid and the motor and prevents losses.
Series ENM and ENT are used for professionale uses or hard applications. On request they can be equipped with a manual by-pass to regulate capacity and head. They are used in agriculture, nautical field, industry, etc. 

SPECIFICATIONS 
- Max flow 16 m3/h, max head 42 m
- Height of priming 6 meters
- Possibility to reverse the flow
- Asyncronous single-phase (ENM) or three-phase (ENT) motor, protection IP 44, with professional switchreverser (see drawing) and cable
- Continuous duty 
- Pumps are supplied with one straight fitting and one curved fitting. 
LIQUID
Max temperature 90° C (130° C with gaskets in Viton)
- Max density 1.1 g/cm3
- Without hard particles (e. g. sand) 
- Not too viscous
- Examples: water, sea water, gasoil, oil, anticryptogamics, etc. 
- Do not use with petrol, solvents and, in general, in places presenting the risk of explosion and fire.
MATERIALS 
Pump body: bronze 
Impeller: bronze
Shaft: inox AISI 316
Counterflange (ENM20 e ENT20): inox AISI 304 

GASKETS / SEALS 
- Lip seal in NBR with stainless steel spring *
On request: 
- tenuta ad anello in Viton
- tenuta meccanica ceramica/grafite/NBR
- tenuta meccanica ceramica/grafite/VITON
- tenuta meccanica carburo di silicio/VITON
- tenuta meccanica ceramica/grafite/EPDM
* O-ring between body and cover in NBR (Viton on request)
* (only ENM 20 and ENT 20) gasket in Guarnital

POWER SUPLY 1~
Standard: 230 Volt / 50 Hz 
On request:
110 Volt / 50 Hz, 110 Volt / 60 Hz, 220 Volt / 60 Hz 

POWER SUPLY 3~
Standard: 400 Volt / 50 Hz
On request:
230 Volt / 50 Hz, 230 Volt / 60 Hz, 400 Volt / 60 Hz 


     
ECC 12
ECC 20  12,24V
ECC 24
ECC 25 έως 40  12,24V

Specifications
 

ECC series (direct current motor)
This series of direct current self-priming electric pumps solves the problem of liquid transfers when a battery is available as power supply. They have a very strong suction capability and they can operate also with discontinuous presence of the liquid at the suction. The particular tight structure of the pump body avoids the contact between the liquid and the motor and prevents losses. On request they can be equipped with a manual by-pass to regulate capacity and head. They are used in the nautical field, on tank trucks, in agriculture, etc.

SPECIFICATIONS 
- Height of priming 6 meters 
- Direct current motor 12 or 24 Volts with terminal board, protection IP 23 
- Continuous duty 
- Pumps are supplied with one straight fitting and one curved fitting. 
LIQUID
- Max temperature 90° C (130° C with gaskets in Viton) 
- Max density 1.1 g/cm3 
- Without hard particles (e. g. sand) 
- Not too viscous 
- Examples: water, sea water, gasoil, oil, anticryptogamics, etc. 
- Do not use with petrol, solvents and, in general, in places presenting the risk of explosion and fire. 
MATERIALS 
- Pump body: bronze
- Impeller: bronze
- Shaft: stainless steel AISI 316
- Counterflange (ECC 12/20
and ECC 24/20): stainless steel AISI 304 

GASKETS / SEALS 
* Lip seal in NBR with stainless steel spring
On request: 
Lip seal in VITON with stainless steel spring
mechanical seal ceramic/graphite/NBR
mechanical seal ceramic/graphite/VITON
mechanical seal silicon carbide/VITON
mechanical seal ceramic/graphite/EPDM

* O-ring between body and cover in NBR (on request in VITON)
* (only ECC 12/20 and ECC 24/20) Counterflange gasket in Guarnital 



I40
IFM
IFE
BS
X

TR

I
IFM
IFE
BS
X
TR


Ι.
With pulley 1A72 for the 20-35 andι 2A72 for the 40-50.  Specifications

IFM. These series of pumps have the same characteristics of series I with bearing and pulley; besides, a mechanical or electromagnetic clutch is interposed between pulley and shaft; this allows coupling to an always running motor with the possibility to start and stop the pump. Pullley 1A110 for the25-50 and 2A100 for the 50.

IFE This series allows to remote-control start and stop of the pump through a simple switch.

BS. These pumps have the same hydraulic performances of series I with bearing and pulley, but they are flanged for connection to hydraulic motors group 2 version B03 (german standard). They are ideal for installation on board of machines equipped with a hydraulic system.

Χ. Pumps series X with overgear 1:6, for coupling to power takeoffs PTO 1"3/8. They are designed mainly for installation on agricultural machines, for example for filling tanks on agricultural trailers for anticryptogamic treatments with water from wells or rivers or for small irrigation installations. They are available is sizes 40 and 50.


TR.
Self-priming pumps arranged to be operated by electric drills. Really useful for small liquid transfers, it is easy to install and to use. The pump body is made of bronze, the shaft of stainless steel. Available in 14 and 20 sizes.



DIESEL KIT 220V 

Diesel Kit 220V
DIESEL KIT 12-24V
Diesel Kit 12V, 24V
Self-priming electric pump type EEM 20 with handle  2 pipes (3 meters each) in special rubber for fuels with fittings in polypropylene 
Suction filter 
Transfer gun in polypropylene  
Self-priming electric pump type ECC 12/20 (12 Volt) or ECC 24/20 (24 Volt) with handle  2 pipes (3 meters each) in special rubber for fuels with fittings in polypropylene 
Transfer gun in polypropylene 
2 cables (2 meters each) with clips for connection to batteries


Stainless steel pumps   Manual
     

ALM20
ALM, ALT 20
AL 25-40
ALM, ALT 25 έως 50


Specifications

 

ALM, ALT series
The best solution for transfers of liquids because of the high self-priming capability, the possibility to operate with discontinuous presence of the liquid at the suction and the reversibility of the flow. The AL series, entirely made of stainless steel AISI 316, is particularly suited for corrosive liquids (chemical agents, fertilizing fluids, sea water) and food fluids (milk, wine, oil, fruit juices). On request they can be equipped with a manual by-pass to regulate capacity and head. They are used in oenology, food and chemical industry, agriculture. 

SPECIFICATIONS
- Max flow 12 m3/h ,max head 40 m
- Height of priming 6 meters 
- Possibility to reverse the flow 
- Pump body, impeller and shaft in stainless steel AISI 316 
- Asyncronous single-phase (ALM) or three-phase (ALT) motor, protection IP 44, with professional rotary switchreverser and cable 
- Continuous duty
LIQUID 
- Max temperature 90° C (130° C with gaskets in Viton) 
- Max density 1.1 g/cm3 
- Without hard particles (e. g. sand) 
- Not too viscous 
- Do not use with petrol, solvents and, in general, in places presenting the risk of explosion and fire. 
MATERIALS
- All wetted parts in AISI316

GASKETS / SEALS
- mechanical seal ceramic/graphite/NBR
on request: 
- mechanical seal ceramic/graphite/VITON 
- mechanical seal silicon carbide/VITON 
- mechanical seal ceramic/graphite/EPDM 
- mechanical seal AISI 316/graphite/TEFLON 
POWER SUPPLY 1~
Standard: 230 V / 50 Hz 
On request:
110 V / 50 Hz, 110 V / 60 Hz, 220 V / 60 Hz 
POWER SUPPLY 3~
Standard: 400 V / 50 Hz 
On request:
230 V / 50 Hz, 230 V / 60 Hz, 400 V / 60 Hz 


     
AL 12-20
AL20  12,24V
AL24-40
AL 25 έως 40  12,24V

Specifications
 
AL series (direct current motor)
The best solution for transfers of liquids because of the high self-priming capability and the possibility to operate with discontinuous presence of the liquid at the suction. The AL series, entirely made of stainless steel AISI 316, is particularly suited for corrosive liquids (sea water, chemical agents, fertilizing fluids) and food fluids (milk, wine, oil, fruit juices). This version with direct current motor (12 or 24 Volts) is used when a battery is available as power supply. On request they can be equipped with a manual by-pass to regulate capacity and head. Fields of use: nautical field, tank trucks, agriculture, etc.

SPECIFICATIONS
- Max flow 9 m3/h ,max head 15 m
- Height of priming 6 meters 
- Possibility to operate with discontinuous presence of the liquid at the suction 
- Pump body, impeller and shaft in stainless steel AISI 316 
- Direct current motor 12 or 24 Volts with terminal board, protection IP 23 
- Continuous duty 
LIQUID 
Max temperature 90° C (130° C with gaskets in Viton) 
- Max density 1.1 g/cm3 
- Without hard particles (e. g. sand) 
- Not too viscous 
- Do not use with petrol, solvents and, in general, in places presenting the risk of explosion and fire.

MATERIALS
- All wetted parts in AISI316

GASKETS / SEALS
mechanical seal ceramic/graphite/NBR
on request: 
- mechanical seal ceramic/graphite/VITON 
- mechanical seal silicon carbide/VITON 
- mechanical seal ceramic/graphite/EPDM 
- mechanical seal AISI 316/graphite/TEFLON 



     
ECC JET
ECC JET  12V, 24V

Specifications
  ECC JET series (direct current motor)
Self priming electri pumps type Jet in stainless steel AISI304 for booster units, with direct current motor.

SPECIFICATIONS
- Max flow 3.6 m3/h ,max head 30 m
-Direct current motor 12 or 24 Volts
with terminal board, continuous duty, protection IP 23 
-Pump self-priming until 8 meters of depth 
-Max temperature of the liquid 60° C 
-Max operating pressure: 6 bar
MATERIALS
-Pump body: stainless steel AISI 304
-Shaft: stainless steel AISI 304
-Diffuser: thermoplastic material 
-Impeller: thermoplastic material 
-Mechanical seal: Ceramic/graphite/NBR

APPLICATIONS
-Booster units on board of ships 
-Suction and transfer of drinkable or clean water from tanks or wells, also if some air is dissolved in the liquid when a battery is available as power supply 
Washing


AL
ALFM
ALFE
ALBS
ALX
AL
ALFM
ALFE
ALBS
ALX

AL. With pulley 1A72 for the 20-35 andι 2A72 for the 40-50.  Specifications

ALFM. These series of pumps have the same characteristics of series I with bearing and pulley; besides, a mechanical or electromagnetic clutch is interposed between pulley and shaft; this allows coupling to an always running motor with the possibility to start and stop the pump. Pullley 1A110 for the25-50 and 2A100 for the 50.

ALFE This series allows to remote-control start and stop of the pump through a simple switch.

ALBS. These pumps have the same hydraulic performances of series I with bearing and pulley, but they are flanged for connection to hydraulic motors group 2 version B03 (german standard). They are ideal for installation on board of machines equipped with a hydraulic system.

ALΧ. Pumps series X with overgear 1:6, for coupling to power takeoffs PTO 1"3/8. They are designed mainly for installation on agricultural machines, for example for filling tanks on agricultural trailers for anticryptogamic treatments with water from wells or rivers or for small irrigation installations. They are available is sizes 40 and 50.



ACCESSORIES FOR TRANSPORT 

- Handle: for all models type 20 and 25, for EEM 30 and EEM 40
- Plate with handle: for all models type 20, 25, 30, 35, 40
- Truck: for all models

ACCESSORIES TO INTEGRATE IN THE PUMP
- Manual bypass to regulate capacity and head.
- Drain cock (for bronze pumps)
- Drain plug (for stainless steel AL pumps)
- Special gaskets
- Hoses type DIN - GAROLA - MACON (for stainless steel AL pumps)
- Motor with protection degree IP 55

ACCESSORIES FOR TRANSFER
- Couple of pipes for gasoil (3 meters each) with suction filter
- Transfer gun in polypropylene for gasoil
- Transfer gun in polypropylene for food liquids
- Transfer gun in aluminum
- Automatic transfer gun
- Liter counter
- Couple of cables with clips for batteries
- Fittings in nylon (for stainless steel AL pumps)
- Fittings in stainless steel (for stainless steel AL pumps)


© Marco Pumps SA - P. Marcomichalis & Son SA  Tel +30 210 4830329 • Fax +30 210 4833358 •  sales@marcopumps.gr       youtube
Webmaster