Products > Circulators, In-Line pumps > Wet rotor electronic circulators DAB

EVOTROΝ, Energy class Α

Enbloc body composed of hydraulic section in cast iron and wet rotor motor. Motor casing in die cast aluminium. Impeller in technopolymer. Motor shaft in ceramic held in graphite bearings lubricated by the pumping medium. Rotor protective jacket, stator jacket, and closing flange in stainless steel. Ceramic thrust ring, ethylene-propylene seal rings and brass air breather plug. The two-pole synchronous wet-rotor motor driven by frequency converter and does not require any form of overload protection.
With special night sleep function.
SPECIFICATIONS
• Max flow 4,2 m3/h, max head 8 m
• With MOTOR AXIS HORIZONTAL
• For clean, free of solids and mineral oils, non-viscous, chemically neutral and approximating the properties of water (max. glycol contents 30%).
• Max working pressure : 10 bar
• Liquid temperature -10°C to +110°C
MOTOR DATA
• Protection rating: IP 44
• Insulation class: F
• Installation: with HORIZONTAL MOTOR SHAFT
• Standard voltage input: single-phase 1 x 230 V / 50 / 60 Hz
• Special versions : for hot water systems, for solar systems

Presentation powerpoint (2ΜΒ)

Specifications

VEA, VEB

SPECIFICATIONS
• Max flow 120 m3/h, max head 11.5 m
• With MOTOR AXIS HORIZONTAL
• For clean, free from solids and mineral oils, non viscous, chemically
neutral, close to the characteristics of water
• Max working pressure : 6 bar (16bar on request)
• Water temperature +15°C to +95°C
ΥΛΙΚΑ
• Pump body in cast iron.
• Motor shaft and rotor protection in stainless steel.
MOTOR DATA
• 2 pole motor
Thanks to the internal protection of the motor, the pump requires no external motor protection device. The pump always starts at average power (elevated torque) regardless of whether normal service or nighttime
reduction (min.) is set.
Zero potential contact for service and fault signalling.
Energy-saving mode (min. 1).
Available on request: analogue module which allows the speed of rotation to be set externally by means of a 0-10 V or 0-20 mA signal.
This product complies with EN 60335-2-51 European Standard.

BPH-E, DPH-E DIALOGUE

DIALOGUE electronic circulation pumps can be used in the heating, ventilation and air conditioning systems of apartment and office blocks such as:
- High-rise apartments - Apartment blocks - Houses
- Clinics and hospitals - Schools - Buildings adapted for offices
All models are available both in the single version as well as in the back-up twin version (DPH-E)
SPECIFICATIONS
• Max flow 60 m3/h, max head 18 m
• With MOTOR AXIS HORIZONTAL
• For clean, free from solids and mineral oils, non viscous, chemically
neutral, close to the characteristics of water
• Max working pressure : 10 bar
• Water temperature -10°C to +120°C
MATERIALS
Enbloc circulation pump made up of cast iron hydraulic parts and an electric asynchronous motor with wet rotor. Aluminium motor casing. High performance volute pump casing thanks to the detailed design and smooth internal surfaces. In-line suction and delivery ports, flanged with threaded connectors for the introduction of the temperature and pressure sockets. Technopolymer rotor, hardened stainless steel motor shaft mounted on graphite bushings that are lubricated by the pumped liquid. Stainless steel rotor and stator liner. Ceramic thrust washer, ethylene propylene grommet and brass air vent cap. Two pole asynchronous
motor.
MOTOR DATA
• 2 pole motor
• Thanks to the internal protection of the motor, the pump requires no external motor protection device.
• Protection ΙΡ44, isolation class Η
• Voltage 1~ 230V/50-60 
The product complies with the EN 61800-3, EN 60335-, EN 60335-2-51 European standards